"industrial ventilation fan"

HG785 Alloyed Steel Industrial Medium Pressure Dust Collector Centrifugal Fan Detail introduction 6-06 series centrifugal fan is generally used for gas transportation of granular or powdery materials, and can be widely used to transport air and non-corrosive non-self-igniting, non-viscous substances. The temperature of the medium generally does not exceed 50C (max 80C), the dust and hard particles contained in the medium is not more than 150 mg / m3. Product features 1. The

Carbon Steel V-Belt Driving High Volume Dust Collector Fan Blower Detail introduction The 4-14 series centrifugal fan is suitable for indoor ventilation in general factories and large buildings. It can be used to input gas as well as to output gas. The gas delivered by the 4-14 series fan should be no more than 80 C air and other gases that are not self-igniting and are not harmful to the human body and are not corrosive to steel materials. No viscous substances are allowed

Heavy Duty V-Belt Driven High Pressure High Wear Resistance Dust Collector Fan Detail introduction 9-03 series fan-type iron furnace special high-pressure centrifugal fan, is suitable for IL/h, 2L/h, 3L/h, 3L/h, 7L/h melting rate of iron furnace blast performance requirements. The fan can also be used as the blast for various furnace forging furnaces. It is also suitable for conveying air and non-corrosive, non-self-igniting, non-viscous materials or light powder/debris/short

Alloy Steel Long Lifetime Explosionproof Dust Collector Centrifugal Fan Detail introduction The fan is suitable for equipped with economizer (heater) and smoke and dust removal device. The fan can output higher gas pressure, and can provide more gas flow at the same time, low noise. In the case of using the common base, the installation is very simple and basically does not require the support of professional technicians. The motor shaft is elastically connected with the

High Air Flow Energy Efficiency Kilns Cooling Dust Collector Fan Detail introduction The 9-10 series centrifugal fan can output high gas pressure, suitable for conveying normal or high temperature clean gas/combustible gas/corrosive gas/mixed with a few impurities, light particles/debris/short fiber materials. Before the induced draft fan, dust removal device with a dust removal efficiency of no less than 85% must be installed to reduce the dust content of the smoke entering

Aluminium Alloyed Energy Saving Radial Blower Dust Collector Fan Detail introduction 1.The fan pressure is high, therefore it is especially suitable for 1-20t/h industrial boilers, which equipped with spiral pipes and multi-tube dust collector. 2.The fan has high efficiency, high total pressure, low noise, flat performance curve, wide economical use area, and adopts backward plate type blades. The efficiency of the fan at the best working point is 86.5%, and the noise index(

Q235 Carbon Structural Steel Impeller Hub Ventilate Heavy Duty Fan Detail introduction Mainly to meet the dust emission requirements of the electric arc furnace exhaust gas purification equipment, improve the workshop environment, to ensure that the dust concentration in the electric furnace working area meets the sanitary standards for industrial enterprises, and can also be used in various occasions with the same functional requirements. The 5-12 series centrifugal fan is

Coupling Driving Backward Carbon Steel Dust Collector Centrifugal Fan Detail introduction 6-06 series centrifugal fan is generally used for gas transportation of granular or powdery materials, and can be widely used to transport air and non-corrosive non-self-igniting, non-viscous substances. The temperature of the medium generally does not exceed 50C (max 80C), the dust and hard particles contained in the medium is not more than 150 mg / m3. Product features 1. According

Single Inlet Energy Efficiency Q345 Dust Collector Blower Fan Detail introduction 6-06 series centrifugal fan is generally used for gas transportation of granular or powdery materials, and can be widely used to transport air and non-corrosive non-self-igniting, non-viscous substances. The temperature of the medium generally does not exceed 50C (max 80C), the dust and hard particles contained in the medium is not more than 150 mg / m3. Product features 1. According to