"industrial centrifugal blower"

High Pressure Q235 Energy Efficiency High Temperature Centrifugal Fan Introduction The 8-12 series strong cooling fan is designed to work in the high efficiency area to achieve energy saving when operating under variable operating conditions. It is jointly designed by the fan energy-saving group of the Ministry of Machinery Industry and organized by the national fan industry. Its a high-performance product promoted by the State Economic Commission and the Ministry of

Large Capacity Long Lifetime Backward Materials Drying Centrifugal Flow Fan Introduction 1. It can output very high pressure and can work at higher medium temperature, suitable for any industrial occasion where high pressure & high temperature gas needs to be delivered. 2. In the case of using the common base , the installation is very simple and basically does not require the support of professional technicians. 3. The bearing box is reserved with the temperature and

High Volume Backward Curved CFB Boiler Centrifugal Flow Fan Introduction The 9-10 series high pressure fan is generally used for forging furnace and high pressure forced ventilation and widely used for material transportation. It is suitable for conveying air and non-corrosive, unnatural and non-viscous gases. The temperature of the medium is generally not more than 80C, and the dust and hard fine particles contained in the medium are not more than 150mg/m3. The fan can also

Alloy Steel High Air Flow High Wear Resistance Drying Centrifugal Flow Fan Introduction At present, there are many series of boilers, and the situation of burning coal quality is quite different, after installing dust removal equipment and waste heat utilization equipment, insufficient pumping force affects normal operation. In order to overcome the insufficient pumping force due to the above reasons, the furnace has a positive pressure, which affects the combustion and

Aluminium Alloyed Antiwear CFB Boiler Explosion Proof Blower Centrifugal Fan Introduction Of Centrifugal Fan G4-10 and Y4-10 series ventilation and induced draft fans are suitable for the ventilation and induced draft fan systems of 2~670T/h steam boilers in thermal power plants. Technical data series model Rotation Speed (r/min) Total Pressure (Pa) Air Capacity (m/h) Power (kW) 4-10 8D 1450 21041400 1615630993 18.55 9D 960 ~ 1450 775 ~ 2668 15229 ~ 44128 11 ~ 37 10D 730 ~

Aluminium Alloyed Heavy Duty Centrifugal Fans Forced Draft Energy Efficiency Introduction The 5-10 series ventilator is a high efficiency and energy saving product developed by our company, which is used for ventilation and exhaust system of smelting, chemical, medicine and dust removal production lines. Bearing seal can be lubricated. Service life is more than L10:80000 hours to ensure operation reliability and durability. Excellent aerodynamic performance, the maximum

Single Inlet Heavy Duty Centrifugal Fans Wear Resistant Fluidized Bed Boiler Introduction The 9-08 series high pressure fan is generally used for forging furnace and high pressure forced ventilation, and can be widely used to transport materials, transport air and non-corrosive, non-self-igniting, non-viscous substances gas. The fan shaft power will not exceed the motor rated power regardless the operation point of the stable working range. Customers can use it without any

Coupling Driven High Temperature Centrifugal Fan Oven Wall Cooling Introduction The 9-08 series high pressure fan is generally used for forging furnace and high pressure forced ventilation, and can be widely used to transport materials, transport air and non-corrosive, non-self-igniting, non-viscous substances gas. Each wheel is subjected to dynamic balance test. The balancing level is kept at G4.0 (Typical products are balanced to G6.3 only). Durable, stable and quietness

HG785 Alloyed Steel High Volume Centrifugal Ventilation Fans Foundry Furnace Introduction Medium requirements for 6-08 series fans: The medium to be transported should be non-corrosive, non-flammable, explosive, and free of viscous substances. The dust and hard particles contained in the medium should be no more than 150mg/m3. Standard centrifugal fans, including single inlet, with a variety of radial bladed, forward curved, backward curved and self-cleaning impellers.