"centrifugal exhaust fan blower"

High Air Flow Corrosion Resistant Industrial Boiler ID Boiler Fan Introduction It is boiler induced draft fan with a total internal pressure efficiency of 90.5% specially designed to be suitable for various coal quality and equipped with a smoke-and-dust removal device (1~20 tons/hour). This type of fan is currently used in the boiler industry. The air volume of the induced draft fan and the difference in wind pressure are relatively large, in order to adapt to the above

Q235 Energy Efficiency Antiwear Heat Dissipation Boiler Blower Fan Introduction The 6-06.51 series boiler fan is mainly used for the fan system of the 2t/h~670t/h steam boiler of the thermal power plant, and also meets the requirements of the performance parameters of the high pressure head of the fluidized bed furnace. This series of fans can also be used for dust removal, mine ventilation and general ventilation systems. The medium transported by the forced draft fan is air

Heavy Duty Long Lifetime Cement Fan Anti Abrasive Forward Introduction The 5-12 series centrifugal fan is an enhanced version of the 5-11 series medium pressure centrifugal fan. Motor is carefully matched to the fan load, protection level IP54, and insulation class F. Motor ball bearings are used and lubricated. Motor and drives are isolated from the air stream to avoid grease or dirt accumulation. Detail introduction Fan shaft shall be heat treated through soaking furnace to

Aluminium Alloyed High Air Flow Air Supply Cement Fan Metallurgy Introduction The 5-12 series centrifugal fan is an enhanced version of the 5-11 series medium pressure centrifugal fan. It is suitable for conveying non-corrosive high temperature gas with the temperature not exceeding 500. If the dust content of the gas is large, the dust removal device with the dust removal efficiency not less than 85% should be equipped before the air inlet of the fan to improve the service

Double Suction Industrial High Temperature Medium Pressure Boiler Fan Introduction Of Centrifugal Fan This type of fan is currently used in the boiler industry. The air volume of the induced draft fan and the difference in wind pressure are relatively large, in order to adapt to the above situation, considering the practicability of the fan, in addition to the 20-ton boiler ID fan need large power coupling direct transmission, the other uses the triangular belt type

Long life fan units for dust collector systems Centrifugal blower fan Introduction The dust-collecting fan has a simple structure, has the characteristics of large flow, low noise, and convenient use. It can quickly collect dust and dirt, and ensure the cleanliness of the work site and exhaust air. Technical data series model Rotation Speed (r/min) Total Pressure (Pa) Air Capacity (m/h) Power (kW) 4-14 2.8A 1450 ~ 2900 166 ~ 970 565 2262 0.55 ~ 1.1 3.15A 1450 ~ 2900 215 ~

Industrial Backward Curved Air Supply Biomass Boiler Centrifugal Fan Introduction The 8-17 series high-pressure small-flow fan is designed for applications requiring high pressure. Under the premise of ensuring a certain amount of air, the full pressure can reach the high pressure requirement. It is mainly used for blasting furnace blast and other forced air supply, and can also be used for tunnels to exhaust or supply air through hard pipes. The fans are divided into general

AC Motor Single Inlet Abrasion Resistant Industrial Kilns Boiler Fan Introduction The 8-17 series high-pressure small-flow fan is designed for applications requiring high pressure. Under the premise of ensuring a certain amount of air, the full pressure can reach the high pressure requirement. It is mainly used for blasting furnace blast and other forced air supply, and can also be used for tunnels to exhaust or supply air through hard pipes. Technical data series model

Q235 Single Inlet Cement Fan High Volume Backward Energy Saving Introduction The gas delivered by the 4-14 series fan should be no more than 80 C air and other gases that are not self-igniting and are not harmful to the human body and are not corrosive to steel materials. No viscous substances are allowed in the gas, and the dust and hard particles contained in the gas are not more than 150 mg/m3. Detail introduction It can also be made into explosion-proof and flame