"industrial blower fan"

Coupling Driving Energy Efficiency Wear Resistant Industrial Centrifugal Fans Introduction The 5-06 series fan can be used in the feeding system of 2-670t/h steam boiler in thermal power plants, it can also meet the requirements of the high-pressure head performance parameters of the fluidized bed furnace. This series of fans can also be used for dust removal, mine ventilation and general ventilation systems. The blower delivers air, and the induced draft fan delivers flue

Alloy Steel Energy Saving Smoke Exhaust Explosion Proof Blower Fan Product Features The 4-10 series large-flow centrifugal fan is the earliest used fan in China, and it is also the most commonly used fan. Suitable for conveying clean air or light materials at normal temperature, most commonly used in industrial furnaces for air supply, light particle/powder/crush/fiber transportation, air drying/cooling of materials, ventilation and smoke exhaust, and other areas. No viscous

Q235 High Air Flow Energy Saving Air Supply Centrifugal Flow Fan Introduction The 5-12 series centrifugal fan is an enhanced version of the 5-11 series medium pressure centrifugal fan. Mainly to meet the dust emission requirements of the electric arc furnace exhaust gas purification equipment, improve the workshop environment, to ensure that the dust concentration in the electric furnace working area meets the sanitary standards for industrial enterprises, and can also be

Q345 Medium Pressure Antiwear Drying Centrifugal Flow Fan Introduction 1. It is capable of outputting a higher outlet pressure while providing more gas flow with lower noise. Stable operation at higher media temperatures. 2. The fan speed can be flexibly set by matching different pulley diameters to make the fan run at the highest efficiency point and reduce energy waste. 3. Motor sliding guides are provided for easy tensioning of the belt to reduce energy loss due to belt

Heavy Duty Long Lifetime Cement Fan Anti Abrasive Forward Introduction The 5-12 series centrifugal fan is an enhanced version of the 5-11 series medium pressure centrifugal fan. Motor is carefully matched to the fan load, protection level IP54, and insulation class F. Motor ball bearings are used and lubricated. Motor and drives are isolated from the air stream to avoid grease or dirt accumulation. Detail introduction Fan shaft shall be heat treated through soaking furnace to

Q235 High Pressure Backward Curved Boiler Fan Calcining Kilns Introduction This series of fan is suitable for conveying non-corrosive, non-spontaneous combustion, temperature does not exceed 700 high temperature gas, dust and hard particles contained in the medium is not more than 150mg/m3. Detail introduction There are 12 forward bending blades on the impeller. After the impeller is formed, the dynamic and static balance and overspeed test are carried out to ensure the

Carbon Steel Single Inlet Energy Efficiency Cement Fan CFB Boiler Introduction The 5-12 series centrifugal fan is an enhanced version of the 5-11 series medium pressure centrifugal fan. The outlet position of the fan is expressed by the outlet Angle of the enclosure: the forward and reverse angles can be made into 0, 45, 90, 135, 180 and 225 Detail introduction 1. impeller: are forward curved blade, static, dynamic balance, so stable and reliable operation. 2. housing:

Aluminium Alloyed High Air Flow Air Supply Cement Fan Metallurgy Introduction The 5-12 series centrifugal fan is an enhanced version of the 5-11 series medium pressure centrifugal fan. It is suitable for conveying non-corrosive high temperature gas with the temperature not exceeding 500. If the dust content of the gas is large, the dust removal device with the dust removal efficiency not less than 85% should be equipped before the air inlet of the fan to improve the service

Coupling Driving Forward High Pressure Centrifugal Fan Lime Kiln Introduction The 9-10 series high pressure fan is generally used for forging furnace and high pressure forced ventilation and widely used for material transportation. Fan inlet shall be aerodynamic design round curved section to transit the air to the wheel cone smoothly, it shall have good commutated effect to reduce turbulence, improve fan efficiency and reduce noise. Detail introduction The wheel has a stable