"centrifugal air blower"

Aluminium Alloyed Energy Efficiency Smelting Furnace Centrifugal Flow Fan Introduction The 9-10 series high pressure fan is generally used for forging furnace and high pressure forced ventilation and widely used for material transportation. It is suitable for conveying air and non-corrosive, unnatural and non-viscous gases. The temperature of the medium is generally not more than 80C, and the dust and hard fine particles contained in the medium are not more than 150mg/m3.

V-Belt Driven Corrosion Resistant Air Purification Material Handling Blower Introduction The 4-09 series large-flow centrifugal fan is the earliest used fan in China, and it is also the most commonly used fan. Suitable for conveying clean air or light materials at normal temperature, most commonly used in industrial furnaces for air supply, light particle/powder/crush/fiber transportation, air drying/cooling of materials, ventilation and smoke exhaust, and other areas. No

16Mn Single Inlet High Temperature Materials Drying Boiler Blower Fan Introduction This series of fans can also be used for dust removal, mine ventilation and general ventilation systems. The blower delivers air, and the induced draft fan delivers flue gas or gas containing foreign particles. It can be used for more than four years when the concentration of impurities is less than 200 mg/m3. If it contains a lot of impurities, it also can be used, but it will shorten the

Heavy Duty High Temperature Backward Cement Kiln Centrifugal Fan Introduction 1.The fan pressure is high, therefore it is especially suitable for 1-20t/h industrial boilers, which equipped with spiral pipes and multi-tube dust collector. 2.The induced draft fan is made into a single suction, different impeller diameter from 400mm to 3000mm. 3.The position of the air outlet of the fan is expressed by the angle of the air outlet of the casing."Left" and "Right" can be made into

V-Belt Driven High Temperature Material Handling Blower Centrifugal Fan Introduction The 5-12 series centrifugal fan is an enhanced version of the 5-11 series medium pressure centrifugal fan. It has a larger output flow than the 5-11 series. It is also used to transport a variety of common gases and hard materials in the industrial field, the application object is exactly the same as 5-11 series fan. Mainly circulating fluidized bed system, smoke exhaust, material drying,

Large Capacity Aluminium Alloyed Cooling Industrial Centrifugal Fans Introduction Of Centrifugal Fan The 4-09 series large-flow centrifugal fan is the earliest used fan in China, and it is also the most commonly used fan. No viscous substances are allowed inside the gas, and the dust and hard particles contained in the gas are larger than 150 mg/m3, and the gas temperature does not exceed 80C. Technical data series model Rotation Speed (r/min) Total Pressure (Pa) Air

Q235 High Air Flow Energy Saving Air Supply Centrifugal Flow Fan Introduction The 5-12 series centrifugal fan is an enhanced version of the 5-11 series medium pressure centrifugal fan. Mainly to meet the dust emission requirements of the electric arc furnace exhaust gas purification equipment, improve the workshop environment, to ensure that the dust concentration in the electric furnace working area meets the sanitary standards for industrial enterprises, and can also be

Aluminium Alloyed V-Belt Driven Smelting Furnace Centrifugal Ventilation Fans Introduction 1.It can output higher outlet pressure and provide more gas flow at the same time, low noise. Stable operation at higher media temperatures. 2. The fan speed can be flexibly set by matching different belt pulley diameters to make the fan run at the highest efficiency point and reduce energy waste. 3. Motor slide guide can be provided for convenient belt tensioning to reduce energy loss

Single Inlet Abrasion Proof Lime Kiln Heavy Duty Centrifugal Fans Detail introduction The 9-10 series high pressure fan is generally used for forging furnace and high pressure forced ventilation and widely used for material transportation. It is suitable for conveying air and non-corrosive, unnatural and non-viscous gases. The temperature of the medium is generally not more than 80C, and the dust and hard fine particles contained in the medium are not more than 150mg/m3.