"induced draft blower"

Aluminium Alloyed Long Lifetime Coal Mill High Pressure Centrifugal Fan Introduction Of Centrifugal Fan Its a high-performance product promoted by the State Economic Commission and the Ministry of Machinery Industry. It has the advantages of high efficiency, low noise, wide performance and high efficiency curve. Applicable to industrial boilers of 5 ~ 35 tons/hour, the similar intake conditions and performance can be adapted, but the maximum temperature should not exceed 250

Q345 V-Belt Driving Heat Dissipation Industrial Centrifugal Fans Introduction Of Centrifugal Fan The 6-06 series boiler fan is mainly used for the fan system of the 2t/h~670t/h steam boiler of the thermal power plant, and also meets the requirements of the performance parameters of the high pressure head of the fluidized bed furnace. Its a widely used medium-pressure heavy-duty centrifugal fan, which is commonly used in industrial systems such as boilers, dust collectors,

Primary Air Pulverized Coal Drying Grey Centrifugal Exhaust Fan Introduction The 9-11 series fan has a large flow rate and moderate pressure. This fan is designed for the purpose of using industrial boiler to work in the high-efficiency area and achieve the energy-saving target. The Primary Air Pulverized Coal Drying Grey Centrifugal Exhaust Fan is suitable for equipped with economizer (heater) and smoke and dust removal device. It is a high-efficiency energy-saving product

Single Suction Energy Saving Backward Curved Cooling Industrial Centrifugal Fans Introduction Of Centrifugal Fan The 6-05 medium-pressure series fan can meet the performance requirements of large flow and high pressure at the same time, and has the characteristics of high efficiency and low noise. It is a series centrifugal fan products with a wide range of performance. The designed max full pressure efficiency is higher than 80% new series boiler ventilation fans and induced

Carbon Steel Long Lifetime Wear Resistant High Pressure Centrifugal Fan Introduction Of Centrifugal Fan The 7-08 series medium pressure centrifugal fan is the latest series of high-efficiency industrial centrifugal fan developed by our company. It has the highest efficiency of 85.4%. It belongs to small flow and medium pressure series. For the material of impeller and main shaft, we will choose high-strength carbon steel, low-alloy steel, high-temperature alloy steel, high

Single Inlet High Temperature Blast Furnace High Pressure Centrifugal Fan Introduction Of Centrifugal Fan The 9-10 series high-pressure centrifugal fan is the latest developed high-efficiency and energy-saving product, whose performance fully meets the aerodynamic performance of general fan 9-08 series, and has the characteristics of high efficiency, low noise, flat performance curve, large flow regulation range and wide efficient area. It is suitable for conveying air and

Double Suction Industrial High Temperature Medium Pressure Boiler Fan Introduction Of Centrifugal Fan This type of fan is currently used in the boiler industry. The air volume of the induced draft fan and the difference in wind pressure are relatively large, in order to adapt to the above situation, considering the practicability of the fan, in addition to the 20-ton boiler ID fan need large power coupling direct transmission, the other uses the triangular belt type

High Air Flow Energy Efficiency Kilns Cooling Dust Collector Fan Detail introduction The 9-10 series centrifugal fan can output high gas pressure, suitable for conveying normal or high temperature clean gas/combustible gas/corrosive gas/mixed with a few impurities, light particles/debris/short fiber materials. Before the induced draft fan, dust removal device with a dust removal efficiency of no less than 85% must be installed to reduce the dust content of the smoke entering

Low Pressure Forward Metallurgy Centrifugal Ventilation Fans Anticorrosion Introduction The 4-10 series centrifugal Fan can be used for indoor ventilation in general factories and large buildings. The converging and streamlined air inlet is made into a unitary structure and bolted to the inlet side of the fan. A device for regulating the flow of the fan, axially mounted in front of the air inlet. The adjustment range is from 0 (full open) to 90(fully closed). Detail